what is hp in engineering drawing

youngsoftleigh76938 May 14, 2022 engineering , in , is , wallpaper Comment

Draw FV and TV as shown. Ans85-When a straight line is inclined to a plane it will meet that plane produced if necessary.

Projection Of Points In Engineering Drawing 3d Animation Different Quadrants Videos Tutorial Engineering Learning

I took the BHP 489 and divided it by the motor efficiency 875 to get a HP 56.

. Width in Length in Horizontal Zone. Line AB has its end A 25 mm above HP and 30 mm in front of VP. The ability to understand the information.

Engineering Drawing Practice for Schools 81 Colleges BUREAU OFINDIANSTANDARDS MANAK BHAVAN 9 BAHADUR SHAH ZAFAR MARG NEW DELHI 110002. ENGINEERING DRAWING GRAPHICS PROJECTION OF POINTS AND LINES SECOND FLOOR SULTAN TOWER. Mark a point a at a height h mm above XY and a at a.

An engineering drawing is a type of technical drawingthat is used to convey information about an object. When I look at this cut sheet it seems like the motor size they have specified is too small. Engineering ANSI and Architectural drawing format sizes.

Engineering Graphics Universal language for engineers. Now the HP is rotated in the clockwise direction for 900 and is obtained in vertical position. Rotate the line AB about the end A keeping f the inclination of AB with VP constant till it becomes parallel to HP.

What are reference planes and what is their use in engineering drawing. 2 Vertical trace-The point of intersection of the line with. I have received the attached cut sheet from the manufacture.

Location of the company or agency. Roll of engineering graphics Visualization. The first four parts listed above provide important information about the actual drawing.

The company or agency that prepared the drawing. In front of VP 2. Reference plane is used by engineers to show their projection of objects and the plane on which the projection of objects like points lines planes solids projects called plane of projectionin practice Orthographic projection uses two principal planes ie horizontal plane HP and vertical plane.

There are of course other drawing. Divide the TV into 12 equal parts and draw the corresponding lateral lines ie generators in FV. Behind VP 3.

In SECOND Quadrant Above HP. This module will cover the non-drawing portions of a print. Engineering Drawing Inch Format Sizes.

SV is seen on the PP. Up to 4 cash back Architectural drawing sizes are based on the ARCH scale while engineering drawing paper sizes are based on the ANSI scale. A title block will typically appear in the bottom-right corner of a drawing and contains information related to the drawing including.

Engineering drawing graphic portion The information contained in the drawing itself will be covered in subsequent modules. While drawing auxiliary projections auxiliary reference lines are used for representing projections. Understanding BHP and HP.

The projections will be seen as given in Figii. Up to 5 cash back Engineering Drawing 2nd Edition by. Engineering Graphics - Projection of points and lines.

V-belts flat-belts and pulleys. ANSI Standard US Engineering Drawing Sizes. The line of intersection of Horizontal plane HP and Vertical plane VP is the main reference line x-y refer Figure 21.

The lines of intersection of auxiliary planes with principal planes are auxiliary reference lines. Mark points p1 p2 p3 p12 at the. In THIRD Quadrant Below HP.

For drawing projections of solids one has to frequently draw projections of lines either parallel to the HP or the VP and inclined to the other with an angle that is between 0 to 90Similarly sometimes the projections of plane surfaces Perpendicular to one and inclined to the other are required to be drawn. Behind VP 4. Individuals who drew checked and approved the drawing and the date they did so.

1 Horizontal trace-The point of intersection of the line with the HP is called the horizontal trace. In FOURTH Quadrant Below HP. A common use is to specify the geometry necessary for the construction of a component and is called a detail drawing.

Projection of Points There are basically nine type of projections of point is space. It is drawn with reference to XY line. Reprographics engineering drawing sketching pictorial projections paper sizes scales conventions in layout lettering and representation of components tolerances assembly drawings K-parts list exercises in machine drawings structural drawings and design.

An AIP inclined at 45 to the HP cuts the cone through the midpoint of the axis. A drawing that contains all information of an object Drawing is important for all branches of engineering. The point in which the line or line produced meets the plane is called its trace.

The Engineering Drawing common to all Engineering Trades is one of the book developed by the Core group members as per the NSQF syllabus. I am in the process of reviewing a shop drawing for an AHU. Engineering Drawing - Projections of Cone with generator on HPwe are explaining the projections of a cone when one of its generators on HP and that generator.

The drawings are linked together by a master drawing or a. Usually a number of drawings are necessary to completely specify even a simple component. Engineering Drawing Formats Menu.

This rotation of the line will bring the end B to the second new Position B2. Tata Engineering Locomotive Co Ltd Jamshedpur SHRI S. The Engineering Drawing common to all Engineering Trades as per NSQF 1st Semester is the outcome of the collective efforts of experts from Field Institutes of DGT champion ITIs for each of the Sectors and.

Selection of machine components such as. Get full access to Engineering Drawing 2nd Edition and 60K other titles with free 10-day trial of OReilly. Orthographic Projection When the projectors are parallel to each other and also.

In FIRST Quadrant Above HP. International Organization for Standardization. AB 2 is the new position of the line AB when it is inclined at f to VP and parallel to HP.

5 Side Views When the observer looks at the object from side ie from his left-hand side or right-hand side the view obtained is called side view SV. All units are as indicated Not preferred. CHANDRASEKHARAN DIRECTOR MECH ENGG BIS Director General BIS Ex-officio iZfer7lhcr.

Rotate the line AB to make it parallel to HP. D-size paper for architectural plans is 24 x 36 inches or 6096 x 9144 millimeters while D-size paper for engineering plans is 22 x 34 or 5588 x 8636 millimeters.

Mechanical Engineering Drawing Wolseley Engine 120 Hp 8 Cylinders Vintage Print Disenos De Unas Ingenieria Mecanica Tecnicas De Dibujo